someone help please im stumped

[moemoe166]

OK WHEN SWITCH IS TURNED ON TURN SIGNALS BLINK HORN BEEPS TACH FLASHES AND NOTHIN WHEN START SWITCH IS HIT,I WAS TOLD IN NEEDED NEW BATTEERY SO $134.00 HD 65989-97B BATTERY LATER STILL THE SAME SHOWING 13.4 VOLTS AND ON A TENDER,NEXT QUESTION WILL IT NEED EHC FLASHED NOW OR NOT AND DO I HAVE TO TAKE TO DEALER TO DO SO,IVE TOOK SIDE COVERS OFF CHECKED ALL CONNECTIONS,AND RUN WIRE STRAIGHT TO STARTER AND IT TURNED OVER, SORRY ITS AN 06 K9:bang:

 

[bigdogtech01]

No you don't need to get the EHC reflashed when installing a new battery. If it has not had the reflash done yet, it might be a good idea to do so anyhow. But this is not the cause of your problem. WHen you hit the start button does the starter click? What about the comp releases? They make noise? If not, it could be right there at that start button. Do the buttons feel like they squishy or do they click a little when you push them in? You might need all new PCBs

 

[DAWG33]

Not sure if you have gotten it fixed yet but if you havent it sure sounds like the EHC to me. I have a 06 K-9 also and have just had the New EHC installed. If you have this done make sure they install a insulated horn wire cuz if not when you hit the horn it will kill the motor. Good Luck hope this helps!!!

 

[BigDogBro1]

Check for crimped tight wire crimps and good battery connections at +/- terminals.

Could it be a bad/cracked RH bar circuit board, collapsed or stuck button dome or connection?

 

[LARS]

No you don't need to get the EHC reflashed when installing a new battery. If it has not had the reflash done yet, it might be a good idea to do so anyhow. But this is not the cause of your problem. WHen you hit the start button does the starter click? What about the comp releases? They make noise? If not, it could be right there at that start button. Do the buttons feel like they squishy or do they click a little when you push them in? You might need all new PCBs

There he is,back at it.Great to have your knowledge flying around again

 

[bruce]

make sure you check for good grounds and ground cable.

 

[moemoe166]

FELLERS I APPRECIATE YOUR HELP IVE TRIED EVERY SUGGESTION I GUESS ITS OFF FOR THE ONE HOUR HAUL TO DEALER

 

[phatchopper300]

No you don't need to get the EHC reflashed when installing a new battery. If it has not had the reflash done yet, it might be a good idea to do so anyhow. But this is not the cause of your problem. WHen you hit the start button does the starter click? What about the comp releases? They make noise? If not, it could be right there at that start button. Do the buttons feel like they squishy or do they click a little when you push them in? You might need all new PCBs

Yep glad to see ya pop in here and post. Hope things are going well for ya. The dog is runnin great. Ride it to work just about every day. Get better gas than the SUV.

 

[erldawg]

If you've checked everything from your other post and still have not found the problem here is a troubleshooting flow chart....Pages 2&3 will help checking the starting button and power to starter solenoid. use an ohm meter to check continuity.

http://www.bigdogbiker.com/forums/attachments/efi-topics/628d1206835121-flowchart-troubleshooting-chart-08diagflowcht.pdf

Here's a wiring diagram to help out.

http://www.bigdogbiker.com/forums/attachments/technical/457d1202952106-2006-2007-wiring-schematic-diagram-wire_diagram_-.pdf